Aviom MixSP Standalone Personal Mixing System
The MixSP Standalone Personal Mixing System is the perfect plug-n-play 6-mixer monitor system for everything from silent rehearsals to live gigs. It allows you to connect mics and/or line-level signals directly to the Pro16 input module without need for a console. The built-in XLR passive split on the AN-16/i-M Mic Input Module can be used to connect the input signals to a PA system or mixing console and retain independent control over the monitor content. It's the perfect solution for performers who travel; no more worrying about the monitor system at the gig!
Once the input signals are connected to the AN-16/i-M Mic Input Module, connect a Cat-5e cable from the AN-16/i-M to the A-16D Pro A-Net Distributor which copies and splits the digital signal while at the same time adding DC power to each of its eight outputs.
Connecting a Cat-5e cable from the A-16D Pro to each A-16II Personal Mixer is all that is necessary to complete the setup; the mixers get their power over the same cable that delivers the 16-channel digital signal. Plug headphones, ear buds, or a wireless in-ear monitoring system into the Personal Mixer and you're ready to start creating custom mixes.
Video Tutorials
MixSP ()
- Monitor Mixing
- Digital Snakes
- Audio Networking
Product Details
The AN-16/i-M Mic Input Module used as the head-end of this system contains 16 high-quality microphone preamps with 24-bit A-to-D converters. Each of its channels contains a continuously variable gain knob, phase reverse switch, 48-volt phantom power, and a rumble filter with an 85Hz rolloff.
The 16-channel A-16II Personal Mixer allows a performer to create and save up to 16 custom mixes, and gives each performer control over channel volume, grouping, pan, stereo spread, along with master volume and tone. The system also includes an MT-1 for each Personal Mixer to allow the personal mixer to be mounted on any standard mic stand.
The A-16D Pro A-Net Distributor eliminates the need to daisy chain Personal Mixers, and simplifies set-up by eliminating the need to connect a power supply to each mixer. The A-16D Pro accepts one Pro16 A-Net input signal and provides nine parallel outputs, using rugged EtherCon connectors and standard Cat-5e cables. The A-16D Pro provides isolated (floating ground) DC power through the eight A-Net Outs; the ninth output is an unpowered A-Net Thru connector, designed for distributing a copy of the A-Net signal to a second A-Net Distributor or remote location.
As with all Aviom personal mixing systems, this six-mix package can be expanded as needed to include more Personal Mixers at any time.
MixSP Technical Specifications
Specs
|
AN-16/i-M Mic Input Module
|
| Audio Inputs |
16, balanced mic- or line-level, XLR combo connector |
XLR Input
(mic/line) |
Pin 1: Ground; Pin 2: Audio +; Pin 3: Audio - |
TRS Line Inputs, &
Send/Return |
Tip: Audio +; Ring: Audio -; Sleeve: Ground |
| Audio Thru |
XLR; Pin 1: Ground; Pin 2: Audio +; Pin 3: Audio -
Direct coupled passive throughput |
| Insert Send |
Impedance balanced; Nominal level: 0dBu; Peak
Level (A/D clip point): +14dBu |
| The Insert Send connector is a line output in the signal path post gain, post filter, and post phase controls. |
| Insert Return |
TRS balanced; Nominal level: 0dBu; Peak Level
(A/D clip point): +14dBu |
| The Insert Return connector is a line input to the signal path that is pre A/D conversion. |
| Analog to Digital Conversion |
48kHz sample rate, 24 bit |
| Operating Level |
+4dBu |
| Frequency Response |
4Hz-22kHz |
| A-Net Output |
One Category 5 (RJ45 connector) |
| A-Net Expansion |
One Category 5 (RJ45 connector) |
| Gain Range |
Mic: +6dB to +60dB; Line: -15dB to +36dB |
| Channel LED Indicators |
Signal Present and Clip, per channel |
| Line Inputs |
Impedance: 48k ohms |
| Metering |
LEDs; green: Signal Present, red: Clip; per channel |
| Stereo Operation |
Stereo Link, per channel pair;
Two-position switch (Normal, Link) |
| Maximum Input Level |
Mic: +14dBu; Line: +28dBu |
| Input Impedance |
Mic: 2.4k ohms; Line (TRS): 33k ohms;
Insert Return: 39k ohms |
| A/D Freq. Response |
-0.1dB @ 20kHz (-0.4dB @ 20.0kHz, measured
from Mic or Line in)
-3dB @ 1.5Hz (-3dB @ 2.0Hz, measured from Mic or Line in) |
| THD +N |
< 0.003% |
| Crosstalk |
-90dB |
| Bit Error Rate (BER) |
10(-12) |
| Signal to Noise (unweighted) |
A/D: -105dB Reference = +14dBu (A/D clip point) Send jack: -113dB (Gain = minimum) |
| EIN (Equivalent Input Noise) |
-128dBu
(Rs = 150 ohms, 20kHz BW, Gain = +60dB) |
| CMRR (Common Mode Rejection Ratio) |
80dB @
120Hz (Gain = +60dB) |
| Low Cut Filter |
-3dB @ 85Hz, -18 dB per octave |
| Phantom Power |
+48 volts, per channel, switch with LED |
| Digital Outputs |
A-Net: 2 (Main and Aux); A-Net Expansion: 1 |
| Pro16 A-Net |
A-Net Expansion combines two A-Net streams (32 channels of audio) onto one Cat-5e cable
uses unshielded Cat-5e UTP (or better) cable
|
| Latency |
<0.880 msec (measured from analog input to analog output) |
| Power Supply |
Internal, universal switching type; IEC jack |
| Voltage |
100-240VAC, 50-60Hz, 60W; Fuse: 250VAC, F4AL |
| Dimensions |
19 x 9.25 in. (482.6 x 234.95mm); 3U high |
| Weight |
12 pounds (5.44 kg) |
|
A-16II Personal Mixer
|
| Audio Output |
1/4-inch TRS stereo, headphone or line level |
| Line/Headphone TRS Output |
Tip: Audio Left; Ring: Audio Right;Sleeve: Ground
Auto-detects mono plugs |
| A-Net Input/Output |
1 A-Net input, 1 A-Net output; Category 5 (RJ45 connector) |
| Digital to Analog Conversion Bit Depth |
24 bit |
| Signal to Noise Ratio |
(Referenced to 0dB) -103dB |
| Latency |
<0.880 msec (measured from analog input to analog output) |
| Pro16 A-Net |
Uses unshielded Cat-5e UTP (or better) cable; maximum 500ft (150m) between devices |
| Tone Controls |
Treble +/-12dB at 9kHz shelving |
| Bass +/-12dB at 160Hz shelving |
| Maximum Levels (RMS) |
Line/Headphone outs: 1.0 watt at 100 ohms |
| Impedance |
Line/Headphone outs: 32 ohms |
Power Supply
Input Voltage
Output Voltage
Plug Size |
External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
18-24 VDC, 0.5 amp
2 mm |
| Dimensions |
10.75" (273 mm) wide x 5.6" (142.2 mm) deep;
2.25" (57.5 mm) high |
| Weight |
3.4 lbs. (1.54 kg) |
| Options |
MT-1 or MT-1a Mic Stand Mount |
| EB-1 Extension Bracket |
| MT-X Expansion Box (requires MT-1) |
| PS-120 Power Supply |
|
A-16D Pro A-Net Distributor
|
| A-Net Input |
One EtherCon RJ45 connector |
| A-Net Thru |
One EtherCon RJ45 connector, unpowered |
| A-Net Outputs |
8 EtherCon RJ45 connectors, powered (DC) |
| LEDs |
Power On; A-Net Active |
| Pro16 A-Net |
16 channels of digital audio over Cat-5e cable |
| Uses unshielded Cat-5e UTP (or better) cable |
| Power Supply |
Internal, universal switching type |
| Cooling |
One ultra-quiet fan |
| Input Voltage |
100-240VAC, 50-60Hz, 60W |
Output Voltage for
Personal Mixers |
18-24 VDC, 0.5 amp |
| Transmitted over the Cat-5e cable |
| Dimensions |
19" (482.6 mm) wide x 14.25" (362 mm) deep; 2U,
3.5" (88.9 mm) high |
| Weight |
12.0 lbs (5.44 kg) |
|
MT-1a Mic Stand Mount
|
| Boxed Weight |
1 lb |
| Boxed Dimensions |
7"w x 5"d x 3"h |
| Dimensions |
6.25" wide at front x 4.5" wide at rear x 3" high |
| Connections: |
Attaches with three screws to bottom of an A360 A-16II, or A-16CS |
| Connectors: |
Size: 6-32, 1/4-inch long screws |
The AN-16/i-M Mic Input Module used as the head-end of this system contains 16 high-quality microphone preamps with 24-bit A-to-D converters. Each of its channels contains a continuously variable gain knob, phase reverse switch, 48-volt phantom power, and a rumble filter with an 85Hz rolloff.
The 16-channel A-16II Personal Mixer allows a performer to create and save up to 16 custom mixes, and gives each performer control over channel volume, grouping, pan, stereo spread, along with master volume and tone. The system also includes an MT-1 for each Personal Mixer to allow the personal mixer to be mounted on any standard mic stand.
The A-16D Pro A-Net Distributor eliminates the need to daisy chain Personal Mixers, and simplifies set-up by eliminating the need to connect a power supply to each mixer. The A-16D Pro accepts one Pro16 A-Net input signal and provides nine parallel outputs, using rugged EtherCon connectors and standard Cat-5e cables. The A-16D Pro provides isolated (floating ground) DC power through the eight A-Net Outs; the ninth output is an unpowered A-Net Thru connector, designed for distributing a copy of the A-Net signal to a second A-Net Distributor or remote location.
As with all Aviom personal mixing systems, this six-mix package can be expanded as needed to include more Personal Mixers at any time.
